Select a Country
  • {{country.Text}}
Select a Language

Quick Lock Sink Mount

Item # {{catalogNumber}}

Quick Lock Sink Mount

Item # {{catalogNumber}}
In Stock
Out of Stock

Available only from InSinkErator®, the "Twist-On, Twist-Off" Quick Lock® design helps ensure fast and easy replacement of existing disposer mounts. This Polished Stainless Steel InSinkErator sink flange will complement most Stainless Steel sinks. The mounting collar configuration is a trademark of Emerson Electric Co.

Show Less
Read More

Reviews / Q&A

  • bvseo_sdk, net_sdk,
  • CLOUD, getAggregateRating, 109ms
  • bvseo-msg: The resource to the URL or file is currently unavailable.;
  • bvseo_sdk, net_sdk,
  • CLOUD, getReviews, 0ms
  • bvseo-msg: The resource to the URL or file is currently unavailable.;

Does this Quick Lock Mount fit the Badger 1 Model?

Asked by: SinkingIn
Answered by: Bob2347
Date published: 2016-03-26

is there a lower profile flange, narrower to allow the unit to sit higher in the cabinet, I need the outlet to be higher for water due to drain height

Asked by: uninformed
Hi, this is Jerica from InSinkErator Customer Service. We only have two types of InSinkErator sink flanges. The regular sink flange requires a 3 ½” sink opening and can accommodate ¾” thickness of sink. The extended sink flange requires the same sink opening and can accommodate 1 ¾” thickness of sink. If you have questions, you may send us an email through [email protected] or you may call InSinkErator AnswerLine at 1 (800) 558-5700. Thank you.
Answered by: Jerica
Date published: 2015-03-28

How can I tighten the 3 screws of the quick lock sink mount. It is too tight around the base to use a flat screw driver?

Asked by: Sjoers
Hello Sjoers This is Jim with InSinkErator. Are you trying to tighten the scews while the disposer is still mounted? If that is the case, you will need to remove the disposer before attempting to tighten the screws. If you have any addtional questions or need additional assistance, please feel free to contact our AnswerLine at 800-558-5700. I hope I have been able to assist you today.
Answered by: InSinkErator
Date published: 2013-12-14

How can I take the mount off an old sink to put it on a new sink?

I recently purchased a new sink and would like to place the quick mount system in this sink. However, I cannot get the mount off the old sink. How can you do this?
Asked by: dsav1722
Hi dsav1722, Thank you for providing visuals of the current setup of your Quick Lock Mount. Based on this, you may start with the following steps below. 1. Using a flathead screwdriver, loosen the 3 screws on the mounting assembly. 2. Using a flathead screwdriver, pry off the snap ring. This will allow you to remove all the other parts of the Quick Lock Mount. 3. Remove the flange from the sink. 4. Remove old plumber’s putty from sink with putty knife. I have included a link below for the generic Installation, Care and Use Manual of our disposers. Kindly refer to steps 6, 7, 8, and 9 for the visuals of the steps above. If you have questions, please do not hesitate to contact us through [email protected] or call InSinkErator AnswerLine at 1 (800) 558-5700. Thank you. Thank you. Sincerely, Jerica
Answered by: Jerica
Date published: 2015-03-21

What is the size of the screw on the mounting assembly?

During a sink upgrade, a screw on the mounting assembly was lost and needs to be replaced so the disposal can be reinstalled.
Asked by: GrandmaL
Hi GrandmaL, This is Belle from InSinkErator Customer Serivce. The size of the mounting assembly screws is 5/16-18X1.13 SET SLOTTED. We have replacement mounting assembly screws available from our authorized parts depot. The part number is 74999. You may contact the authorized parts depot, Carroll Parts at 1-800-654-3545. If you have any other questions, you may contact the AnswerLine at 1-800-558-5700. Thank you.
Answered by: BelleISE
Date published: 2014-10-04
  • y_2018, m_5, d_24, h_7CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.8
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_29
  • loc_, sid_050375002437, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_insinkerator
  • bvseo_sdk, net_sdk,
  • CLOUD, getContent, 31ms